Equipment Commissioning report – A.B.B Egypt
Official Acceptance – Hunter Douglas Chennai
Appreciation Of Our Paint Shop Installed In Volvo Japan
Prime Electrical Commissioning Training
POV – Completion
letter
Appreciation letter from ABB(Egypt)
Appreciation letter from Volvo (India)
Appreciation letter from TTK Prestige
Appreciation letter from
GMR
Appreciation letter from Dickinson Fowler
Appreciation Letter from
REL
TIRTH completion
certificate
Appreciation Letter from SCHINDLER
Hunter Douglas 10+ Years Consistent Performance Certificate
Multi electric 18+ Years Consistent Performance Certificate
Lighting Technologies 10+ Years Consistent Performance Certificate
VENDOR PERFORMANCE RATING APPRAISAL SHEET
We have done performance rating on data collected between the period from 01-Dec-09 to 31-May-10.
Suzlon Generators Ltd
This is to state that Prism Surface Coatings P Ltd, Bangalore have supplied us a paint booth measuring 12m x 5m x 5m and a sanding booth of similar dimensions along with all accessories vide our Purchase Order No.4100003903 dated 03.03.2007. This is working satisfactorily for the last 4 years since commissioning.
Thanks & Warm Regards,
Mr.Viresh Tripathi
(Sr.Executive – Engg. & Maint.)
Toyota Tsusho India Private Limited.
We would like to inform you that the Shower Tester Booth System supplied by you against our Purchase Order has been installed as on 31st March 2011 at Plant#2 of Toyota Kirloskar Motor Pvt. Ltd., Bidadi. The installation is complete except few points (as discussed & informed) which need to be attended by PRISM Surface Coating as early as possible by deputing your members.
Sripathi Bairi.T
General Manager
Aspick
Dear Ganesan,
For the last seven months, we received no Heat & Control orders which required bead blasting.
After getting the bead blasting room ready, all SS jobs that we got were for pressure vessels and heat exchangers or heavier jobs that required no bead blasting.
We got a varilift order last month which had to be bead blasted. It was with great anticipation that we did the pooja yesterday on Janmashtami and wanted to start up but the compressor did not work since we had used it for a long time.
This morning the Atlas Copco guys came and found a contactor stuck and repaired it.
We have been blasting for the last 90 minutes and the dust outside the room is virtually nil.
We are also able to stand inside the door and see the blasting without any dust on ourselves.
We will open up the draw at the bottom of the bag filters this evening and see how much dust is there.
Thanks for a great job.
Regards
Chinny
Volvo India Limited, Peenya
“The performance of the down – draught (water type) paint booth and Curing oven installed at our Peenya facility in 2005, which was then part of M/s Ingersoll Rand (I) Limited, has been satisfactory till date.
This facility currently has been part of Volvo (I) Limited, which took over the Road Machinery Business from IngersollRand (I) Limited in year 2007.”
Dinesh
Manager – Production Engineering
Marko Ahlin
“The company M/S Prism Surface Coatings P Ltd from India made project and managed the construction (put together) machinery. The project covered the operation of powder (dry) coating equipment, including pre-treatment, racks, overhead tracks, hand and automatic spray equipment and ovens, waste water treatment and solving of non-routine problems. Design of project was limited o the one hand by available free space and on the other hand by low cost.
A balance or equilibrium among the four project dimensions: cost, schedule, feature set and quality was achieved. Especially we would like to lay great stress on balance between cost and feature set.
The quality of coating components meets standards likewise the quality of treated water. Operative costs derived of equipment are according to the expectation.
The powder coating plant supplied by M/S Prism Surface Coatings P Ltd, India is performing well. We have no problems even in service after sales”
Director
OCEAN -d.o.o Kamnik-, Slovenia.
Al-Omania Powder Coating Co. LLC, Oman.
“We at OPC wish you and your team continued success in your concerted effort to establish Prism’s credentials in the international scenario. A Company is known by the people it keeps and your team does credit to Prism & you. Best regards”
Mr Arun Kalbag
Managing Director
General Control Group Co- (GCG), Kuwait.
“Thank you very much for your early response regarding the VFD problems. We made modification and changes as per your instructions and found VFD is working normal. We hereby confirm that Mr Satish, your site engineer has successfully erected and commissioned the Powder Coating Plant according to the specifications in the order.
The above plant is running and we are taking regular production.
We do thank you for your co-operation. Best regards,”
Mr Mohammed Al-Bassam
Managing Director
L & T Demag Plastics Machinery Limited, Chennai, India.
“PRISM Surface Coatings’ commissioning team has done a very good job.“
Mr Murugesan
Plant In-Charge
